Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Help
Login
Register
Minnesota Classic Glastron Forum
»
General Category
»
General Discussion
»
Something doesn't look right
« previous
next »
Print
Pages: [
1
]
Author
Topic: Something doesn't look right (Read 2629 times)
0 Members and 1 Guest are viewing this topic.
Retro Performance
Hero Member
Posts: 1049
Something doesn't look right
«
on:
December 23, 2014, 06:17:34 PM »
I don't know if I have ever seen this before........anybody have any ideas on a cause? This is a 90 Mercury circa 1990's
Logged
Hyperacme
Administrator
Hero Member
Posts: 13323
Re: Something doesn't look right
«
Reply #1 on:
December 23, 2014, 06:24:10 PM »
You would think it would blow a hole in piston (which it did) before it blew the head off ?
That must have been one heck of a BANG !
Would frozen water in cylinder do that, if there wasn't a hole in piston ?
Is there a hole in piston ?
Hard to see on laptop ...
Logged
Retro Performance
Hero Member
Posts: 1049
Re: Something doesn't look right
«
Reply #2 on:
December 23, 2014, 06:46:04 PM »
My photos are not so good....there actually is not a hole in the piston but the lighter area around the outside of the piston is damaged. Whatever broke the casting snapped all the gussets around the combustion chamber....
«
Last Edit: December 23, 2014, 07:01:12 PM by Retro Performance
»
Logged
Hyperacme
Administrator
Hero Member
Posts: 13323
Re: Something doesn't look right
«
Reply #3 on:
December 23, 2014, 07:03:42 PM »
What did the owner say ?
Would think the piston would go first ...
Was water jacket bent / damaged ?
Casting flaw ?
Maybe Rich has an idea ...
Time for a new E-TEC ...
Logged
Jason
Global Moderator
Hero Member
Posts: 5564
1974 CV16SS, 1986 CV23
Re: Something doesn't look right
«
Reply #4 on:
December 23, 2014, 07:05:32 PM »
wow!
Logged
Jason S.
1974 Glastron Carlson CV16SS 140 I/O
1986 Glastron Carlson CV23 260 I/O
Retro Performance
Hero Member
Posts: 1049
Re: Something doesn't look right
«
Reply #5 on:
December 23, 2014, 07:09:29 PM »
It is a trade in....knew it had zero compression on that cylinder......just checking to see if it was worth rebuild
no information from owner.....I do not think the water jacket was bent....seems like it ran for a lot of years if it was a casting issue....the broken piece does not seem porous?
seems like hydraulic or freeze damage?......look how clean the combustion chamber is?
Logged
74 Carlson the II
Sr. Member
Posts: 252
74 CV16
Re: Something doesn't look right
«
Reply #6 on:
December 23, 2014, 08:17:37 PM »
The original 1150/115 that was on the pickle did the similar thing, but on mine it cracked the cylinder head in half right through the middle of the spark plug hole. All do from the inner exhaust cover gasket that was sucked in towards the the cylinder ports which allowed water into the cylinder and hydro locked.The pickle sat in storage for 10 years after my father's thumb was ripped off from a water ski rope accident and I'm guessing the gaskets dried out and deteriorated from sitting and not being used. That's where the new 115 had come in to play.
Logged
Steve
74 CV16 115 merc inline 87'
76 CV16 115 merc inline 76' 1150
72 CV19 outboard, no engine YET. Speed? (Unlimited)!!!!!!
74 Carlson the II
Sr. Member
Posts: 252
74 CV16
Re: Something doesn't look right
«
Reply #7 on:
December 23, 2014, 08:22:16 PM »
The head piece that is broken out is way to clean like it has been getting water in there for a while. Steam cleaned.
Logged
Steve
74 CV16 115 merc inline 87'
76 CV16 115 merc inline 76' 1150
72 CV19 outboard, no engine YET. Speed? (Unlimited)!!!!!!
OleRed
Hero Member
Posts: 1688
Re: Something doesn't look right
«
Reply #8 on:
December 24, 2014, 12:58:41 AM »
fuel or water in the third firing order can do just that, motor fires up on the first and second cyl, third one has obstruction, fuel, water, aint got a chance, gotta pop
Logged
1980 23ft Scimitar
Print
Pages: [
1
]
« previous
next »
Minnesota Classic Glastron Forum
»
General Category
»
General Discussion
»
Something doesn't look right