Minnesota Classic Glastron Forum
General Category => Members Profiles / Introductions => Topic started by: buckz6319 on July 05, 2013, 11:24:09 AM
-
Hey, from Ga!
I look forward to all the information, tips, tricks, pics, that will help me with my restoring of my newly required 1975 Glastron-Carlson CV-16, don't know much about this boat, except it has a great racing heritage , great boat builder behind the name. I have always wanted one of these styles, now I have one. I'll be looking, searching, reading, sharing info
thanks for letting this Ga boy join in on all the fun!
-
Welcome ...
-
thank you!
-
Hi Buck, you've just joined one of the best support groups on earth for the Glastron/Carlson addiction! Great folks here always willing to help with info and advise, don't be afraid to ask questions. What part of GA are you in? I live in Jackson (about 15 min from Lake Jackson), but work in Forest Park near the Atlanta airport. Don't be afraid to give a shout if you need anything, glad to help where/when I can.
-
Thanks, and i live in Griffin, Ga, just went through Jackson about an hour ago to get Fresh Air B B Q and take wife to Macon to shop
Have been to lake Jackson many times in the past
Thanks for the offer
Pm me sometime
-
Few problem spots in the CV's ...
First is the small half round drain in rear, hole's were drilled 2 inches above bottom of hull ... so water sat in bottom of hull and absorbed in to flotation foam and stringer wood. The rear two feet of my floor was also rotted from water splashing on it.
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/d2-4.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/d2-4.jpg.html)
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/d2-5.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/d2-5.jpg.html)
PO didn't seal holes for speedo pilot tube mounts and my transom was rotted/cut in half ...
Yours might be OK if PO sealed your right ...
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/d3-2.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/d3-2.jpg.html)
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/d3-1.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/d3-1.jpg.html)
Some how water got in on the left side and rotted upper left corner of transom, foam was dry and top was sealed with glass, so don't know what happened there ...
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/cvt1_zps4e29dde3.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/cvt1_zps4e29dde3.jpg.html)
(http://i131.photobucket.com/albums/p286/Hyperacme/76%20CV16%20blue/cvt2_zpsa3d6efc9.jpg) (http://s131.photobucket.com/user/Hyperacme/media/76%20CV16%20blue/cvt2_zpsa3d6efc9.jpg.html)
JimmyTheMuffler on CGOA site made his drain bowl larger ... Kind of wish I'd done that also ...
Link to his restro ...
http://www.classicglastron.com/phpbb/viewtopic.php?f=20&t=7704 (http://www.classicglastron.com/phpbb/viewtopic.php?f=20&t=7704)
I talked to a guy about replacing transom with out splitting deck/hull but went with the split to do it RIGHT ...
Igor's resrto is here ...
1974 Glastron Carlson CV 16super
http://www.classicglastron.com/phpbb/viewtopic.php?f=34&t=7520 (http://www.classicglastron.com/phpbb/viewtopic.php?f=34&t=7520)
If your finish/flake is dull read here ...
1972 CV-16SS
http://www.classicglastron.com/phpbb/viewtopic.php?f=34&t=7954 (http://www.classicglastron.com/phpbb/viewtopic.php?f=34&t=7954)
Here a section that will come in handy ...
Vendor and Repair Resources
http://forum.cgoamn.com/index.php?board=7.0 (http://forum.cgoamn.com/index.php?board=7.0)
Mark S. is your local Glastron expert and can help with local info.
His restro is a VERY GOOD read ... It's not a CV but much will apply to what your going to be doing ...
http://www.classicglastron.com/phpbb/viewtopic.php?f=28&t=4433 (http://www.classicglastron.com/phpbb/viewtopic.php?f=28&t=4433)
Need more help ...Just let us know ...
-
Thank you all for the links and pics:)
I guess it's time for me to start a thread, show some pics and get some advice on a budget restoration if possible, it will be slow go, but I need to do this for me and the boat
thanks again
now I'm going to start that thread now!
-
my restore link
http://forum.cgoamn.com/index.php?topic=4415.0 (http://forum.cgoamn.com/index.php?topic=4415.0)