Author Topic: Trailer roller replacement  (Read 3691 times)

0 Members and 1 Guest are viewing this topic.

Offline C512Jim

  • Sr. Member
  • ****
  • Posts: 159
Trailer roller replacement
« on: April 03, 2018, 08:43:50 AM »
Since most of my boats are in the 70's to 80's, the trailers are original to the boats and the rubber rollers are showing their age. The few bunk style trailers not so bad, its not too bad to replace a keel v type roller here and there.  The shore-lander style trailers, the support rollers are quite costly if you were to replace all at one time.  Any ideas on economical ways and outlets to keep nice usable rollers protecting your hull.  Thought about marking in some way the old ones if not all are bad and leaving new ones unmarked. 

Offline RedOctober89

  • Sr. Member
  • ****
  • Posts: 154
Re: Trailer roller replacement
« Reply #1 on: April 03, 2018, 09:58:41 AM »
What about removing the rollers and putting a carpeted 2x4 in place of them? More support, less scuffing, no more black marks on your hull? Still get to keep the equaload of the roller setup
Andrew C.
1989 Glastron Carlson 23 CSS 350 Mag - Red October
Follow the project on Instagram: redoctober89

Offline Hyperacme

  • Administrator
  • Hero Member
  • *****
  • Posts: 13462

Offline C512Jim

  • Sr. Member
  • ****
  • Posts: 159
Re: Trailer roller replacement
« Reply #3 on: April 03, 2018, 11:09:19 AM »
Thanks Greg for the link, that looks like way better prices than I have found if I replace Rollers.  Andrews comment about changing to bunk, I have actually wondered about that and if the hulls were actually designed for rollers and if its harder on the hull than a bunk would be.  I get the part about no skuff marks and actually where i launch my boats its easy to float off a bunk because of depth.  I am guessing the right bunk supports might be better than roller bunks. 

Offline RedOctober89

  • Sr. Member
  • ****
  • Posts: 154
Re: Trailer roller replacement
« Reply #4 on: April 03, 2018, 02:12:31 PM »
I just remember Shawn's dimples on his 23 hull from the roller trailer, I have yet to flip mine and see if its the same or not. Makes sense since each roller actually only has a couple square inches of surface contact to the hull, where a bunk would be significantly more. However I have never loaded or unloaded with a roller trailer so I can't say how great they are, and how beneficial a roller trailer is!

I do plan to add bunks under the main engine stringers for more support since the boat will see many miles on the highway.

If its cost savings I would think the wood would be cheaper, but even spraying a bit of paint on all the old ones and replace a couple every year would be better than a big hit upfront.
Andrew C.
1989 Glastron Carlson 23 CSS 350 Mag - Red October
Follow the project on Instagram: redoctober89

Offline Plugcheck

  • Donate members
  • Hero Member
  • *****
  • Posts: 3267
Re: Trailer roller replacement
« Reply #5 on: April 03, 2018, 04:50:04 PM »
I loathe roller trailers, and somewhat of a disdain for folks who power load boats at the ramp.  My druthers?  Find a way to convert to bunk if the cost is anywhere near roller replacement.  I use etrailer.com exclusively, great service, good prices, and smoking fast shipping.  Ya think hull rollers are spendy?  The center keel rollers are spendy as well.
Michael
1979 CVZ-18 388 CI Vortec Mouse
1980 CVX-16SS 140 Mercruiser
1979 CVX-16 Johnson 175
2002 Bennington 2275CC 90 Mercury
1985 Intimidator project
1989 Lowe 200 Redneck fishin Toon
2001 Godfrey Sweetwater pontoon 115 Rude

Offline C512Jim

  • Sr. Member
  • ****
  • Posts: 159
Re: Trailer roller replacement
« Reply #6 on: April 03, 2018, 05:11:02 PM »
I tend to agree that at least in my situation and having access to nice deep launches where we boat I might be better off with two bunks either side of center to get the most support possible.  Taking into consideration like mentioned supporting motor stringer areas if possible.  With the CV27 might need a couple extra short ones in the back just for one side of the motor.  Will take a look back on the videos with mikes CV27.

Offline carlsoncvx18

  • Donate members
  • Hero Member
  • *****
  • Posts: 1588
Re: Trailer roller replacement
« Reply #7 on: April 03, 2018, 06:44:12 PM »
Hear is a pic of a 27 on bunks
1987 CVX18.     1968 Glastron alpha sail boat
1977 GT150
1986 CV23
1984 Intimiadator
1981 CV27
1969 V-180 fundeck

Offline Plugcheck

  • Donate members
  • Hero Member
  • *****
  • Posts: 3267
Re: Trailer roller replacement
« Reply #8 on: April 03, 2018, 08:00:49 PM »
Here is a pic of my Baja 260 trailer.  The bunks are 2x6, tandam axle with surge tongue brakes.
Michael
1979 CVZ-18 388 CI Vortec Mouse
1980 CVX-16SS 140 Mercruiser
1979 CVX-16 Johnson 175
2002 Bennington 2275CC 90 Mercury
1985 Intimidator project
1989 Lowe 200 Redneck fishin Toon
2001 Godfrey Sweetwater pontoon 115 Rude

Offline C512Jim

  • Sr. Member
  • ****
  • Posts: 159
Re: Trailer roller replacement
« Reply #9 on: April 03, 2018, 08:57:09 PM »
definately looks like the way to go.  Thanks for all the input everyone. 

Offline V153

  • Hero Member
  • *****
  • Posts: 4970
Re: Trailer roller replacement
« Reply #10 on: April 04, 2018, 04:25:45 PM »
Good for you. With these boats bunks are the only way to go.
'81 C500_given away, bought back_75.1 mph
'81 Baja 15SS_140 Frankenrude_66.7 mph
'70 something SpeedCraft_(Allison 16R Clone)_69.0 mph
'79 CVZ19_given away
'71 V153_54.8 mph_wrecked


WALK TALL AND CARRY A BIG BILGE PUMP

Offline Diamond Chad

  • Administrator
  • Hero Member
  • *****
  • Posts: 524
Re: Trailer roller replacement
« Reply #11 on: August 09, 2018, 02:47:36 PM »
Switching to Bunks. New (to me) Trailer for the CVX-18. I knocked down all the little rust rock chips with wire wheel, slathered in Coroseal rust chemical converter, primed, rattle can painted, and coated the front sides of the crossmembers with white spray PlastiDip to keep from future chips.  I wonder if the boat will fit?  Had a SX175 I/O on it before.

« Last Edit: August 09, 2018, 03:55:03 PM by Diamond Chad »
2012 GTR 160 Collectors Edition
87 CVX-18 5.7 (Sold)
88 CVX-16 115 Merc  (Sold)
57 Dunphy Imperial Musky - 57 Golden Javelin
01 Malibu Sunsetter 21 LSV 340 EFI

Offline Plugcheck

  • Donate members
  • Hero Member
  • *****
  • Posts: 3267
Re: Trailer roller replacement
« Reply #12 on: August 09, 2018, 03:02:33 PM »
      I'd kinda like to see the hull supported by 4 bunks, but two would probably work.   They appear high enough that keel rollers may not be required depending on the ramps you use.   At shallow ramps it helps to have the end roller to set the bow attitude.   I think you will like bunks, I feel they support the hull better on glass boats.   
Michael
1979 CVZ-18 388 CI Vortec Mouse
1980 CVX-16SS 140 Mercruiser
1979 CVX-16 Johnson 175
2002 Bennington 2275CC 90 Mercury
1985 Intimidator project
1989 Lowe 200 Redneck fishin Toon
2001 Godfrey Sweetwater pontoon 115 Rude