Minnesota Classic Glastron Forum

General Category => Classified / Wanted to Buy => Topic started by: Shrom CVX-18 on February 07, 2011, 08:34:35 PM

Title: Hatch screws
Post by: Shrom CVX-18 on February 07, 2011, 08:34:35 PM
OK guys I have been thing about reproducing these hatch screws for at least the CVX-18. (not sure what else they will fit.) I have made up a blue print of the screw from my CVX-18. I am wondering how many people might be interested in purchasing a pair, if I were to produce them? They would not be an exact replica however I would make sure to make vary similar. They will be stainless machined finished (not polished) I would only sell in pairs that way you have no problems with matching. I work at a machine shop, I am going to have my boss give me a quote on a batch of 10. As soon as I get that quote from him I will post the selling price and ask again who all will be interested. If I have enough I will go through with it and post a add on here showing a picture. Right now if you could reply if you are at all interested that would help. Thanks again
Title: Re: Hatch screws
Post by: dorelse on February 07, 2011, 10:04:21 PM
interested in 2, or maybe four for backups...
Title: Re: Hatch screws
Post by: Burnin Daylight on February 08, 2011, 07:45:03 AM
Shrom you know I'm interested I will take at least one set and that thought of a backup set is not a bad idea.  Just count me in for 4 what the heck. 
Title: Re: Hatch screws
Post by: ChfBrianB on February 08, 2011, 08:33:00 AM
I would love to have a set!
Title: Re: Hatch screws
Post by: CVX Fever on February 08, 2011, 09:06:47 AM
I'd take 2 just to have an extra set.
Title: Re: Hatch screws
Post by: Gotesh on February 08, 2011, 12:17:22 PM
Put me down for a set.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 08, 2011, 04:56:26 PM
OK guys, thank you for the interest. I gave my boss the print and he is going to give me a quote when he gets the chance here soon. The material it will be made of is 316 stainless. Which is the good stuff. A little more expensive then your typlical 303 stainless, but worth it. No worries about it being in the weather. Believe it or not the 303 series stainless does rust over time. Anyhow Hopefully by the end of this week I will have a price for what I set will be. Once I have that price listed, I will have you guys that are interested give me a call and put in your order.
Title: Re: Hatch screws
Post by: MikeB on February 12, 2011, 12:46:43 PM
If these will fit a CVX-16 Hatch I'm interested in a couple sets.  When you get a chance, post a picture and I can check if it will work.  Thanks!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 13, 2011, 08:14:07 PM
If these will fit a CVX-16 Hatch I'm interested in a couple sets.  When you get a chance, post a picture and I can check if it will work.  Thanks!

Hey I do nopt have any new replicas made yet. I am still waiting on a quote from my boss yet. But here is a pictures of what an original screw looks like. The new ones that I will make will be nearly the same thing.


(http://i131.photobucket.com/albums/p286/Hyperacme/CGOAmn/hatchscrew1.png)
Title: Re: Hatch screws
Post by: MikeB on February 13, 2011, 08:22:19 PM
Yep, I'm pretty sure that's exactly what I need.  Put me down for 2 sets if you do end up getting these made.  Thanks!
Title: Re: Hatch screws
Post by: CVX Fever on February 14, 2011, 12:04:28 PM
The CVX16, 18 and 20 used the same screw and recptacle to secure the engine covers. Glastron Carlson part # 121140512. Description reads "Screw Assembly". From my 1980 GC small parts catalog the receptacle appears to be a purchased Southco part and I'm speculating the retainer, which is what Shrom is having made, was a unique GC part.  
Title: Re: Hatch screws
Post by: wexrocks on February 14, 2011, 05:06:31 PM
I researched this, and it was actually a Southco product (the screw) as well. the problem was that the distributors don't have a listing for them in the correct dimensions, only shorter ones. I went back and forth with the distributor trying to find out if they were available from the factory, or if a batch could be made (for all of us). I was eventually told to pick something from what was available, and then no replies or response at all, so I gave up. I think this should be a good alternative, as I've mentioned in another thread, Shrom is a good guy and won't jerk anyone around, and will make sure the quality is good. he knows how much we all love these boats and how detail oriented some of us are, as he is too. I know I'll be getting a set for the Intimidator while they're available.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 14, 2011, 06:41:42 PM
Hey I want to thank you for being patient. My boss today told me that he hasn't forgot about getting me a quote. He has just simply been busy. 
I might need some help from you guys that still have the originals in hand...I made the mistake of selling mine before I could produce them. So what I have to go by is a print that I had made up before I sold them. So if anyone would trust me enough to send one to me. ( i'll pay shipping cost) that would greatly help me on having them made to the same specs.(we can workout the details if someone is willing) One thing I must say is the new ones that I will have made, will not have the *Censored * on the top like the originals. Having that put on will make the cost a bit more. and probably not worth it.  If you would really want that *Censored * in it then I can do that on my own time for a special order. For a price.
Title: Re: Hatch screws
Post by: Burnin Daylight on February 15, 2011, 07:05:44 AM
Shrom, I only have one left and Olered and I are still lake testing burnin daylight on warm days.  We should be finished in a couple of weeks and could probably pull it then.
Title: Re: Hatch screws
Post by: CVX Fever on February 15, 2011, 10:16:45 AM
Shrom - When I'm up at my lake place in a couple of weeks I can bring one home and send it to you.

So Barb if you wanna hold onto yours you can. I won't be getting the boat out until May.   
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 15, 2011, 11:18:37 AM
Thanks guys that will help out alot. That way I have somthing we can look at to copy as we make the first couple parts.


CVX Fever- I sent you a PM

If I get these made, I should be able to have them ready for everyone this season.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 22, 2011, 05:01:14 PM
OK guys the price is in....Kinda pricey But for a set it will be $50 and whatever shipping will be. I would be having him make me 20 sets (40 pcs) I would be paying him the money to have them made, and you guys would be buying them directly from me. Of course If I were having him make more the price would be cheaper however, there was not that much interest to do more. In fact with the interest I got, I will still have aprox 10 sets that I will be trying to sell after would possibly sell to you guys.

So with the price in, Those of you that are still interested please if you could reply to me again that would be great. If enough of you guys or girls are still interested then I will have them made.  If you want to contact me personally send me a PM and I will give you my cell number and we can talk.
Title: Re: Hatch screws
Post by: CVX Fever on February 22, 2011, 07:18:09 PM
I'm still in for a set. About what I figured they would cost to machine out of 316SS in a small batch size.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 22, 2011, 07:55:52 PM
I'm sorry guys $40 a set not $50 I miss calculated. Cheaper then I thought. Unfortunately our shop is not the cheapest however we focus on quality of our work. Every part in are shop goes through a inspection before  it goes out the door .
Title: Re: Hatch screws
Post by: ChfBrianB on February 23, 2011, 09:34:23 AM
I'm in!
Title: Re: Hatch screws
Post by: dorelse on February 23, 2011, 10:26:17 AM
I'm in for 1 set.
Title: Re: Hatch screws
Post by: Gotesh on February 23, 2011, 02:05:46 PM
Count me in for 1 set.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 23, 2011, 07:16:05 PM
Alright guys. I decided that I am going to go through with this. I just talked to CVX Fever on the phone he is going to be sending me a original screw for me to make up and new print to go by. Also to have one in hand for us to look at as they are made. Keep in mind I work as a machinist at this shop and will be right there in the shop while they are being ran. So I personally will be making sure they look good as our lathe guy runs them.
 One thing I want to point out again that I pointed out before. They will not have the slot on the top, mainly because that would be a hole other step on a milling machine and would make the cost more.(who really uses that slot anyway?) Without the slot all the work will be done on the lathe in one program. If you absolutely would want the slot on the top talk to me and I can do that on my time for a extra price. So with in the next few weeks I will be getting a new print made and hopefully get the order in to my boss. I will keep updating on this forum so keep checking in. I can not at this point tell you when they will be done by. I will not know that till i give him the go ahead and set a date for him to have a done.

Please let me know if you want a set, if you haven't already sense the price was listed.( It will help me keep reminding that ppl will buy these and I wont be stuck with them) ???
Title: Re: Hatch screws
Post by: catchnedge on February 23, 2011, 07:37:48 PM
Shrom, thanks for doing this!  Not sure how expensive these will be, but if they are not too bad in cost, may want to consider having a few extra made for down the road, as some club members aquire the boats that need them... (like possibly me :))... just a thought. 

Just FYI...  Not trying to steal thread, but your topic got me thinking about it again, just to let everyone know... I just recently had a batch of steering wheel inserts made... you know the thin aluminum (original are wafer thin aluminum)ones with three holes, that are missing on many of the plastic Glastron steering wheels from the early 70s-80's boats (I think those are the years anyway).  Well, I had an original from my old GT-150 and I had a big batch made using thin stainless.  I just haven't had the time to get pictures and advertise them yet.  I plan on doing that in the next week.  I will sell them at my cost... more details to follow.   I will advertise them here first!
Title: Re: Hatch screws
Post by: MarkS on February 23, 2011, 07:44:58 PM
I'll take three of the steering wheel inserts Mark, just let me know when and how much.   ;)  Once again, sorry for thread jumping Shrom.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 23, 2011, 08:08:31 PM
Shrom, thanks for doing this!  Not sure how expensive these will be, but if they are not too bad in cost, may want to consider having a few extra made for down the road, as some club members aquire the boats that need them... (like possibly me :))... just a thought. 

Just FYI...  Not trying to steal thread, but your topic got me thinking about it again, just to let everyone know... I just recently had a batch of steering wheel inserts made... you know the thin aluminum (original are wafer thin aluminum)ones with three holes, that are missing on many of the plastic Glastron steering wheels from the early 70s-80's boats (I think those are the years anyway).  Well, I had an original from my old GT-150 and I had a big batch made using thin stainless.  I just haven't had the time to get pictures and advertise them yet.  I plan on doing that in the next week.  I will sell them at my cost... more details to follow.   I will advertise them here first!

Take a look back through the thread. More info is there. but the cost is $40 a set.(two screws)
Title: Re: Hatch screws
Post by: catchnedge on February 23, 2011, 08:16:15 PM
gotcha, just didn't look closely... yea, not easy to make many extra of those.  That's not a bad price for a good quality set though.  My inserts were much cheaper to produce, so I was able to make a bunch... I just wasn't thinking, a lot of work is going into these screws.  Thanks again.

Mark, will do...
Title: Re: Hatch screws
Post by: Burnin Daylight on February 24, 2011, 05:11:19 PM
Shrom count me in for a couple sets.  Been outta town for the week.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 25, 2011, 07:23:52 PM
Shrom count me in for a couple sets.  Been outta town for the week.

OK sounds good Burnin Daylight Thanks...( I feel like I should know every ones names, but I don't sorry :-/)
I mentioned to my boss today that I was going to have him do the job once I have a revised print made up and have the original screw to go off of. He told me he is glad to do it for us. One thing that He did say, that I wont all of you guys to know is that our shop is pretty busy and these won't get done till probably month of May. So Once I have these made up I will post pictures and get back to everyone. So I can start taking orders and get them shipped out.

I will keep everyone updated through this forum as I get stuff done like New print, and when give the official order in to my boss.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 06, 2011, 07:45:46 AM
The Original hatch screw arrived in the mail yesterday, thanks to CVX Fever. He was so nice to lend it to me. This week I will make up a new print and put in the order to my boss by next week hopefully.

Thanks again CVX Fever for being so kind to do this!!
Title: Re: Hatch screws
Post by: Burnin Daylight on March 06, 2011, 04:25:43 PM
Thanks from me too.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 15, 2011, 07:13:15 PM
hey just wanted to update you guys/girls. I got the new print done last night and will be giving it to my boss this week. I hope that he can get them done sooner then May. But just plan for now not to see them anytime before then. Maybe he will put it higher on the stack of prints for me sense I have been giving him a lot of overtime the past month.  ;D

While we are waiting for these to be done, I would like to ask everyone that will be purchasing a set, to PM me your real Name/handle on this site. This will allow me to make a list up and have it all ready when the screws are done. This is simple to help me out on time. If you could include your address that would be great too. If you do not want to give that out till later that is fine also.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 16, 2011, 07:06:02 PM
Forgot to add, Please in the personal message if you are purchasing more then one set. Make sure you tell me that in the PM. Otherwise I will assume you only want one set.

Payment methods will figured out when the time comes. I prefer Paypal if you have it.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 21, 2011, 11:22:31 AM
Boss told me today that he is going to try and run the hatch screws next week. A lot soon then expected  ;)
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 31, 2011, 06:31:27 PM
Just an update for those who are purchasing and for those who are interested but not sure yet.  We ordered in the material and had to order more inserts for doing the threads. Once they come in we should be running the screws off. I am sorry this is taking so long. I guess better late then never. right? Anyhow I am enjoying this process, I feel as if I am making new friends on here because of it. Never thought i would have friends in MN.
Title: Re: Hatch screws
Post by: Burnin Daylight on April 04, 2011, 02:01:37 PM
Hey Shrom, OleRed and I are in Oklahoma and I never knew anyone from PA.
Title: Re: Hatch screws
Post by: CVX Fever on April 04, 2011, 04:17:54 PM
Hey Shrom everyone is just glad your making these available. No one thinks it's taking too long. As Doug would say, carry on! ;D
Title: Re: Hatch screws
Post by: dorelse on April 04, 2011, 04:21:18 PM
Yeah, I mean, the MN boys are going to be flooded for a while and I'm in no hurry, so don't sweat it.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on April 04, 2011, 04:32:08 PM
Thanks guys. I'm just the type of person that like to see something done as soon as possible. :) So I guess it just feels like it is taking to long to me...
Title: Re: Hatch screws
Post by: Shrom CVX-18 on April 26, 2011, 03:57:29 PM
We started running the parts at the end of the day today! So I should have pictures of them and up for sale by the end of the week. Some of you might have noticed that originals are kinda loose screwing into the receivers.  These new screws I am making are a nicer more positive fit. Still loose enough to screw in by hand, but should be tight enough to hopefully solve the problem of them loosening up from vibration! I will keep you guys posted. It this point I think it is safe to say that by this weekend they will be done.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on April 27, 2011, 06:24:44 PM
OK guys here is this finished product. Again these are sold as a pair. (two screws) for the $40 plus shipping. I will need your address to determine the shipping cost. Some of you have already given me your address. Now I just need to know how you will be paying.

These will be sent USPS mail.

Payment:    Paypal, or Money Order.

Please PM if interested, Include in your PM:  Address and # of sets you would like to purchase, Payment method (If you are paying with PayPal include your email that is linked to your account, and I will send you an invoice.) Please feel free to call me a 717-419-2553 if you would prefer.

I only have 20 sets as of now. So get them while you can. I am not sure when or if I will be making another batch.

Just some things I want to point out: These do NOT have the slot on the tops. They are not made from factory print. They are made from a Original sample part. They have some minor differences, that being the reason I am only selling as a pair. Extra cost to have slot put on top.( Not determined yet) They screw into Original receiver mounts on the boat. These should work on the following model Carlsons. CVX-16, CVX-18, CVX-20, Intimidator. If you know these will fit other please let me know.

 Pictures below, The one that is screwed into the receiver is the new product!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on April 27, 2011, 06:25:42 PM
more pitcures
Title: Re: Hatch screws
Post by: CVX Fever on April 27, 2011, 07:07:45 PM
Hey Shrom they look awesome! 8)
Title: Re: Hatch screws
Post by: dorelse on April 28, 2011, 09:11:52 PM
Shrom - They will also be used on the CVZ-18's...
Title: Re: Hatch screws
Post by: Shrom CVX-18 on April 29, 2011, 02:55:25 PM
Shrom - They will also be used on the CVZ-18's...

 Thank you I knew I was forgetting a model.
Title: Re: Hatch screws
Post by: ChfBrianB on May 26, 2011, 10:11:13 AM
Recieved the screws last week!  Thanks!  They look great!  I need to get the clips though.  The new screws don't work in my old clips...

Any ideas?
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 26, 2011, 11:18:27 AM
Recieved the screws last week!  Thanks!  They look great!  I need to get the clips though.  The new screws don't work in my old clips...

Any ideas?
Hmm. That surprises me that they don't work. Steve gave me one of his for when we ran them. I made sure they all went on to that clip. Maybe it's just tight? I have no problem refunding you if you want.  But you will have to ship them back. I hope we can make them work though.
Title: Re: Hatch screws
Post by: CVX Fever on May 26, 2011, 12:22:02 PM
Mine both work so I'm not sure what the issue is that Brian is having unless the orginal recievers were changed out. I've got BOM's w/part numbers for all the 1979 Carlsons and per that they used the same latching system on the CVX16, 18, 20, etc. One thing I've learned about the company since owning 2 Carlsons is that they used a lot of the same parts on different models/years.

Try screwing it in without going though the hood first. It may just be a little tight. On my boat one side is snug and the other is pretty loose using the same screw. You may just need to adjust the prongs on the reciever with a small flat screwdrive if you can't get the screw started.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 26, 2011, 03:53:24 PM
Yeah I agree try and adjust your "fingers" on your receiver and see what that does.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 28, 2011, 12:45:58 PM
Recieved the screws last week!  Thanks!  They look great!  I need to get the clips though.  The new screws don't work in my old clips...

Any ideas?

 Did you get them to work?
Title: Re: Hatch screws
Post by: CVX Fever on May 31, 2011, 04:43:27 PM
Quote
Did you get them to work?

Brian - I'm also curious to know what the verdict ended up being. Sure hate to see people buy these only to find out they don't work and then poor Craig is stuck with all the mucking around that goes with returns.

Please let us know what you found out - Thanks Kip
Title: Re: Hatch screws
Post by: dorelse on June 15, 2011, 09:24:40 AM
Shrom - Sending you a PM...I need a set!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on June 15, 2011, 07:38:28 PM
Shrom - Sending you a PM...I need a set!

 I have a set ready for you! Still haven't got a PM yet though  ??? I'll be at the lake all next week. If you need to contact me I can give you my number.
Title: Re: Hatch screws
Post by: Burnin Daylight on June 19, 2011, 01:44:33 PM
Craig, I finally got my hatch screws installed on the intimidator and they look great and fit perfectly.  Great job machining those. Thanks again.
Title: Re: Hatch screws
Post by: dorelse on June 21, 2011, 10:14:09 AM
Same here Shrom, mine look great & fit perfectly.  Those are some big screws!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on June 23, 2011, 11:20:09 AM
Glad to hear that guys! Thanks for the compliments, it was fun to do. Would love to see pictures posted when you have a chance. Still have a few sets to sell if anyone else is interested. Everyone that i talked to before i machined them kept their word and purchased them from me. I am vary thankful for that! Not sure that i will be making another batch, so if you haven't got a set yet. Get them now while you can.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on July 14, 2011, 08:12:42 PM
Does anybody have these new hatch screws installed? I would love to see pictures!
Title: Re: Hatch screws
Post by: dorelse on July 14, 2011, 08:18:11 PM
Yep:

(https://lh5.googleusercontent.com/-oexAgrxoPCU/ThjYpi_WuTI/AAAAAAAAGys/8IVcVyqQyBM/s800/100_0001-1.JPG)

(https://lh5.googleusercontent.com/-JJ7NwJqHHeI/ThjYqo3yQ7I/AAAAAAAAGyw/e5unprxFAeg/s800/100_0002-1.JPG)
Title: Re: Hatch screws
Post by: Shrom CVX-18 on July 14, 2011, 08:23:40 PM
Awesome! Thank you. I am super happy to be apart of helping you guys out on your projects.
Title: Re: Hatch screws
Post by: dorelse on July 14, 2011, 08:33:14 PM
I'm really glad I bought and extra set...they're going straight to the bottom if the ever get dropped.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on July 16, 2011, 01:36:37 PM
I'm really glad I bought and extra set...they're going straight to the bottom if the ever get dropped.

Find a washer that has a 1/4 hole. Cut a slot in the washer. Bend it just enough to thread it on the screw after installed. That should help hold those screws is so that they don't fall out. After you have it threaded on try and flatten the washer again. That should do the trick.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 01, 2011, 06:51:24 PM
Got a picture from Barb of the hatch screws on her intimidator. Thought I would share.
(hope you don't mind Barb ;D) What a nice boat she has!
Title: Re: Hatch screws
Post by: Tonka Jim on August 01, 2011, 07:36:29 PM

Find a washer that has a 1/4 hole. Cut a slot in the washer. Bend it just enough to thread it on the screw after installed. That should help hold those screws is so that they don't fall out. After you have it threaded on try and flatten the washer again. That should do the trick.

A 1/4" lock washer works good
Title: Re: Hatch screws
Post by: MarkS on August 02, 2011, 08:37:02 AM
Quote
Got a picture from Barb of the hatch screws on her intimidator. Thought I would share.
(hope you don't mind Barb Grin) What a nice boat she has!
She sure does!  One of the coolest parts (to me) is the "backlit" Carlson in the dash.  Great work all the way around, IMHO.    :P
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 07, 2011, 05:14:24 PM
OK guys just a little update. I have only have 6 sets of these hatch screws left. After these are gone I highly doubt I will have more made. If enough people start asking again about them. Then I might. Will probably not make extra though. 

 Also just thought I would share some of the locations in which these have been shipped to sofar.

Thought it was neat. Sold a set to a guy in Belgium, and as follows OH, KY, MN, IA, PA. Probably a couple other places also, but I didn't wright down all of them.
Title: Re: Hatch screws
Post by: MarkS on August 07, 2011, 06:44:57 PM
Didn't Barb get a set, she's in OK!?
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 07, 2011, 07:59:37 PM
Didn't Barb get a set, she's in OK!?
You bet she did. That OH was meant to be OK, but It looks like I did sell a set to OH also haha
Title: Re: Hatch screws
Post by: dorelse on August 07, 2011, 11:24:30 PM
You did the clubs a great service by taking the chance and making a set.  I'm glad I got and extra set!!!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on October 19, 2011, 04:51:02 PM
Last of this Batch was Just sold...No worries to those of you that still want a set. I am going to keep a list of those who would like a set. Once I have enough interested I will have my shop run another batch. So if you want to be on the list please PM or call 717-419-2553.
Title: Re: Hatch screws
Post by: DanR on November 02, 2011, 07:49:38 AM
I don't want to step on any toes here, but I also work in a machine shop. I just asked my boss what he'd charge for these parts. He said about $5-$6 a piece if we ran at least 50. We just ran a part that was pretty much the same. We also have live tooling so we can put the slot on it as well.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on November 02, 2011, 11:05:54 AM
Well that's cheap. I'll pass that part on for you to make then. No way my shop could make them that cheap. Unless we would start to run alot of them. You said yoy run parts like it already that helps. We are a small shop,but high quality. I dont think I'll even bother making more if you can get them done for cheaper.
Title: Re: Hatch screws
Post by: DanR on November 02, 2011, 07:26:21 PM
We make medical stuff; like bone drills, bone taps, knee replacements, that kind of thing. We are a small shop too, and my boss is still stuck in the 80's, probably why the low price. If we had a sample part or a detailed drawing, I could start making them tonight.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on November 08, 2011, 07:50:56 PM
We make medical stuff; like bone drills, bone taps, knee replacements, that kind of thing. We are a small shop too, and my boss is still stuck in the 80's, probably why the low price. If we had a sample part or a detailed drawing, I could start making them tonight.


I know with this first run that I did, some of the cost was just the programing alone. I spent a decent amount of time just measuring the original part and making a detailed print. So I think if I were to run another batch could have a better price. But I can't say for sure how much better.

 Let me know if you plan to take over on this. as I will back down. and let you do the work.
Title: Re: Hatch screws
Post by: DanR on December 02, 2011, 03:14:49 PM
I do the programming and setting up, I told the boss I'd do that on my time. That's why our price would be so much lower I'd guess.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on December 03, 2011, 06:53:09 AM
I do the programming and setting up, I told the boss I'd do that on my time. That's why our price would be so much lower I'd guess.

I will pass along this thread to you. Your welcome to start making the screws. I know some ppl will be happier with the price. I have had ppl complain about how much they were. But I just don't think they realize the work involved, and that these are more of a custom part. Not you typical screw you can buy in the hardware store.
Title: Re: Hatch screws
Post by: still_fishin on December 03, 2011, 09:28:57 AM
Ill take a set.
Title: Re: Hatch screws
Post by: DanR on January 30, 2012, 07:47:38 AM
I'll either need some dimentions or a sample part to make them. Sorry I've been away from the site for a while. I'll check in more often.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 11, 2012, 08:34:19 AM
I'll either need some dimentions or a sample part to make them. Sorry I've been away from the site for a while. I'll check in more often.
Sent you a PM. Let me know what your intentions are with this.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 13, 2012, 07:09:06 PM
still_fishin, I am willing to run another batch of hatch screws, but I need more interest to keep the cost down.  So till then you will be on the list. Keep an eye on this thread. I will update when I have more interest from here or elsewhere.
Title: Re: Hatch screws
Post by: dorelse on February 13, 2012, 09:02:34 PM
I do have an extra set if the waiting list is a long time yet Shrom...
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 15, 2012, 04:22:46 PM
I do have an extra set if the waiting list is a long time yet Shrom...

Thanks, I'll let you offer up that set if you would like. As of this point there really isn't much of a list. Doesn't seem to be much more interest. So I will wait a while yet see if more ppl contact me. Otherwize I can run a couple sets in the ProtoTRAK Lathe myself. If its only one or two ppl that would want a set. I would have to figure out a price for that though.
Title: Re: Hatch screws
Post by: still_fishin on February 15, 2012, 10:56:24 PM
Hold off on making me a set. I'm thinking I might use a didn't latching mechanism similar to my 18. Thanks though.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on February 19, 2012, 11:08:53 AM
Hold off on making me a set. I'm thinking I might use a didn't latching mechanism similar to my 18. Thanks though.

Alright sounds good. I must say I have a CVX-18 myself. and even though I make these hatch screws, mine own Carlson doesn't even sport my product.
Title: Re: Hatch screws
Post by: DanR on February 23, 2012, 09:02:07 AM
Looks like I'll just back away slowly on this one. I wasn't trying to undercut you, I know you're not making anything on these. I was just going to donate my time to program and set-up the machine to keep the cost down. I didn't mean to step on any toes, just trying to save some fellow boaters some gas cash!
Title: Re: Hatch screws
Post by: Shrom CVX-18 on March 12, 2012, 06:03:18 PM
OK guys, I have had a few interests in more hatch screws to be made. I am going to have my boss re quote me on the price sense we already have the programing done. So Should be cheaper, but unsure of how much.

I have had a few ppl say that their boat no longer has the original receivers on their boat. So I am thinking of possibly coming up with design for new receivers also. To sell if needed. 

I will keep you updated.

Feel free to PM or with any interest in the screws.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 21, 2012, 05:21:02 PM
Guys, I have been back in forth whether or not to make more hatch screws. Mainly because of the cost I would have to put into these upfront of my own money, Not knowing when or whether they will sell. I would like to see more interest posted. I have had a few ppl contact me which helps, but my fiance and I decided to  go ahead and put in a order for another batch and see how it goes.  We love these style boats and want to help out others that have the same love.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on July 24, 2012, 04:43:46 PM
More Hatch screws here.

Please email me cmshrom07@yahoo.com or call 717-419-2553

Price $40 a set. (two screws)

I will need your address to determine shipping cost of you are outside the US.
Title: Re: Hatch screws
Post by: Hotwired on July 26, 2012, 11:17:02 PM
Anyone have the receivers that these screw into?  I would kind of like to put some on my CV-16 but have nothing to thread them into.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on July 27, 2012, 04:03:34 PM
Anyone have the receivers that these screw into?  I would kind of like to put some on my CV-16 but have nothing to thread them into.
I am finding a few ppl that has the same problem as you. So I'm trying to come up with a receiver for these screws that will work. That way I can sell them as needed.  They will not be like the originals though. :-/ But would work just as well.

I can't decide if I wont to try and make them out of spring steal like the originals our just make the stainless or Alum...Stainless or Alum would be easier for me. do not have a way to bend or cut the hole out of spring steal as the originals are made.   
Title: Re: Hatch screws
Post by: DanR on October 17, 2012, 07:58:35 AM
I see on FaceBook that these are not going to be made after this batch is gone. My offer still stands. All I need is a sample part and I can make them. I'll even put the slot in like the originals! PM me if needed. I may not check the site every day, but I do often enough.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on October 17, 2012, 08:13:09 AM
I see on FaceBook that these are not going to be made after this batch is gone. My offer still stands. All I need is a sample part and I can make them. I'll even put the slot in like the originals! PM me if needed. I may not check the site every day, but I do often enough.
its all you from here on out. I can not afford to put upfront the cash to have them made anymore. I have had to may ppl email me saying they want a set and not commit to purchasing after I have them made. So now I am sitting on these screw, and out the cash that should be going into my boat.
Title: Re: Hatch screws
Post by: DanR on October 18, 2012, 07:44:33 AM
I'll wait til you sell out. I can make them as needed. I do the programming, setting up and also run them. I can do it on my own time and just get charged for the material. That'll help keep the price down.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on November 09, 2012, 07:00:21 PM
I'll wait til you sell out. I can make them as needed. I do the programming, setting up and also run them. I can do it on my own time and just get charged for the material. That'll help keep the price down.


Thanks! I still have 10 sets left  :-/ Sounds like you have you own shop to do this. Should deff keep the price down if your just charging material.  If your interested in my print send me a PM I can also send you a blemish Hatch screw also.
Title: Re: Hatch screws
Post by: Johnbond008 on January 17, 2013, 06:10:02 PM
I'm a new member today, count me in on a set. THX John.
Title: Re: Hatch screws
Post by: Hyperacme on January 17, 2013, 06:15:13 PM
Welcome to CGOAMN Mr. Bond !

You should go in to Shrom's profile and email or PM him  ...
Title: Re: Hatch screws
Post by: Shrom CVX-18 on January 17, 2013, 06:22:25 PM
I'm a new member today, count me in on a set. THX John.

Welcome! Give me a call 717-419-2553. I still have some left.!
Title: Re: Hatch screws
Post by: Burnin Daylight on January 17, 2013, 07:48:59 PM
I bought 2 sets, one for my Intimidator and one in the safe for later!!  Thanks Craig!
Title: Re: Hatch screws
Post by: hv.drenth on March 16, 2014, 05:00:58 PM
I have 1 set fits great . Have the originele one at home in the safe and the copi in the engine cover ....


Verzonden vanaf mijn iPhone met behulp van Tapatalk
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 04, 2014, 04:22:24 PM
Thanks Guys, I enjoyed having these made for you guys. Sorry That I have not been active on this forum or any forum lately, Life got busy and just not enough time in the day it seems, plus extra cash to be playing with my toys (Boat/jeep) There is a guy on facebook saying he can making them cheaper. So I'm leaving it up to him to try and produce these at a cheaper price and help more Carlson owners out.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 13, 2015, 07:29:26 PM
If there is interest I'm thinking of running another batch of hatch screws. I am unaware the other guy taking over on making these, like I had said. Please post on here and share the word, so that I can possibly make this happen to help out those who are in need of hatch screws.
Title: Re: Hatch screws
Post by: DanR on May 20, 2015, 12:23:12 AM
I quit that job where I could have made these. I never saw any people have any interest in having them made. I didn't want to step on your toes, last I saw, you still had 10 sets to unload.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on May 20, 2015, 07:38:55 PM
If there is interest I'm thinking of running another batch of hatch screws. I am unaware the other guy taking over on making these, like I had said. Please post on here and share the word, so that I can possibly make this happen to help out those who are in need of hatch screws.

No problem. If some one can make them cheaper and help others out that's fine. I've been busy and money has been tight. I could not afford to pay the cost upfront.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 06, 2015, 08:24:20 PM
New batch of hatch screws made up. Limited supply, I'm offering Engraving of your boat model for an extra $5 a set.  This batch I took some extra time and polished up the head a bit for a better shine. Email me at Cmshrom07@yahoo.com.
Title: Re: Hatch screws
Post by: Shrom CVX-18 on August 21, 2015, 08:30:40 PM
:)