Glastron/Carlson windshields ...

[Hyperacme]

Please add to this if you know of others ...
I'll edit to keep it easy to read.


1976/1987 CV23 = Inside Windshield Dimensions: 64 1/2 L x 0 W x 0 H
1977/1988 CVX 18 & CVX20 = Inside Windshield Dimensions: 73 L x 0 W x 20 H
1979/1980 19ft CVZ = Inside Windshield Dimensions: 40 L x 9 W x 16 5/8 H
1981 C500 & C537 Metric & 1986 CVX 17ft = Inside Windshield Dimensions: 61 L x 21 W x 17 H
1977/1990 CVX16 = Inside Windshield Dimensions: 65 L x 0 W x 16 H             
1977/1980 CVX18 & CVX20 = Inside Windshield Dimensions: 73 L x 0 W x 20 H
1973/1974 CV21 = Inside Windshield Dimensions: 76 L x 16 W x 20 1/4 H
1971/1973 CV19 = Inside Windshield Dimensions: 72 L x 14 1/2 W x 18 1/2 H
1973 CV16SS = Inside Windshield Dimensions: 63 L x 13 W x 11 1/2 H
1974 CV16 = Inside Windshield Dimensions: 63 L x 13 W x 12 3/8 H
1976 CV16 = Inside Windshield Dimensions: 63 L x 13 W x 12 1/4 H
All GT150 & GT160 = Inside Windshield Dimensions: 64 L x 12 W x 11 3/4 H


American Runabouts
https://www.facebook.com/bootrestauration/?hc_ref=ARREuWvgcp6L5-2Yg81f6fe9u6E8rwTRgwPSPfOF66XCPWJMJ2bnaR2gCjevXiQWBfo&fref=nf


Stellar Plastics Fabricating
https://www.stellarplastics.com/
14121 Gratiot Ave.
Detroit, Michigan
48205
Phone : 313-527-7337



Upd Plastics ..

https://www.updplastics.com/windshieldsproducts/glastron-boat-windshields-1950s-1960s/

https://www.updplastics.com/windshieldsproducts/glastron-boat-windshields-1970s-early-2000s/

https://www.updplastics.com/windshieldsproducts/glastron-boat-windshields-2000s/



Crown Plastic inc.  in Plymouth
http://crownplasticsinc.com/


Eaton Quade
http://www.eatonquade.com/


ePlastics.com
http://www.eplastics.com/


Wayne Earl Mfg Inc.
http://www.wayneearl.com/default.asp


Custom Mold & Tint Inc.
http://getaboatwindshield.com/home


The Plastic Guy
http://www.theplasticsguy.com/boat-windshield-gallery.html


Taylor Made , Parts ...
https://www.taylormadeproducts.com/hardware/

Wyman Boathouse & Restoration / Cloquet, MN.
http://www.wymanboats.com/?fbclid=IwAR0lGR7cjdRs-uuv9YNL_Ud2-lZQPIiByuMq5MUfTKH2iJSAl9dgtEVaM6o

Finney / Lake Havasu City, AZ
http://www.finneys.com/

Composites Plus ..
http://compositesplusrepair.com/

Middy Marine Products Inc
9320 151ST Ave NE Redmond, WA, 98052
Phone: (425) 883-4600

Steele Rubber Products
https://www.steelerubber.com/marine
6180 HIGHWAY 150 E
DENVER NC 28037-9650
PHONE: 800-447-0849
LOCAL: 704-483-9343
EMAIL: contact@steelerubber.com

Third Coast Plastics
http://thirdcoastplastics.com/
https://www.facebook.com/ThirdCoastPlastics
13940 Bammel North Houston Rd, Ste 207
Houston, TX 77066
(832) 649-7622

Kren plastics ...
http://www.krenplastics.com/profile.html

Walsh Plastics Ltd ...
http://www.walsh-plastics.com/

Steele Rubber Products.
https://www.steelerubber.com/

Performance Acrylics
169 longview Ave west , Mansfield, OH, United States, Ohio  (419) 564-6475
https://www.facebook.com/profile.php?id=100043007511338

[Burnin Daylight]

These guys "Frankie" made the windscreen for Burnin Daylight and the T-tops and winglets for OleReds scimitar.  Frankie also made the custom  LED lit dash and the instrument panel for the larger instruments for Burnin Daylight, so he has the mold for the cvx 20 instrument panel.

http://www.eatonquade.com/

[Hyperacme]

American Runabouts  /  How to make a boat windscreen out of acrylic
https://www.youtube.com/watch?v=TdYzOnorjg4

Jerry's windshield ...
http://forum.cgoamn.com/index.php?topic=3030.0

[Hyperacme]

CV windshield channel & hardware …

Taylor made .. Glazing Assembly Vinyls
https://www.taylormadeproducts.com/hardware/glazing-assembly-vinyls/

Link to white trim on horsehead_traders eBay store …
https://www.ebay.com/sch/horsehead_traders/m.html?item=361073454913&rt=nc&_trksid=p2047675.l2562





Taylor Made Products Deck Channel White Vinyl 110 In TAY-826500
http://www.jmsonline.net/deck-channel-white-vinyl.htm



Original gaskets,the large one is the bottom and the small is the top that seals the windshield and the channel.






Original next to new Taylor Made channel ...




U-Channel for windshield frames
http://www.allglassparts.com/


Gray vinyl paint for white channel ...
https://www.semproducts.com/marine-refinish/vinyl-coattm

[Hyperacme]

CVX16 / CVX18 / CVX20 windshield hardware

From Joe ...

truss head screw.
http://www.fastenal.com/web/products/details/0170577?searchMode=productSearch&filterByVendingMachine=
the washers are harder to find but allied elec has these, white nylon made for #10 and #12 truss head screws.
http://www.alliedelec.com/search/productdetail.aspx?SKU=70147593&mkwid=sjqzSeszr&pcrid=23493289097&pkw=w-1573&pmt=b&pdv=c&gclid=CI_L28HG9cECFQYFaQod1nIArA


From Chad ...

these might be good to add a more finished look, snap caps.
http://www.homedepot.com/p/Everbilt-10-Black-Hinged-Pan-Head-Screw-Cover-3-Piece-816028/204275903


From Brian ...

There in the electric dep. at manards close to the zip ties and wire nuts. It's what I've used on a couple of my projects. Drill a 3/8"hole in the plexi, put the 1/4" grommets in, then use a 1/4" ss screw-bolt with a nylon nut and just snug them, not to tight so they can flex. Work great!

[Hyperacme]

Thanks to Steven E Johnson ...

Make your own GT / CV windshield.

Just finished stripping and polishing the windshield frame on my CV16. And formed a new windshield from 3/16" Plexiglas using a buck that I made from MDF.

 I will try to explain further.

Remove the original glass.
Using a small amount of spray adhesive, stick a big enough piece of paper to it and trace the outline. Transfer the outline to your new Plexiglas. Cut out using a jigsaw with a fine to medium cut blade on the slow. Slowest speed possible.

 Use your frames to trace the shape for each buck. Start in the center heating up the new windshield to get the first bend.
Tape the glass down to keep it from shifting. Proceed to one side and continue to heat and bend and tape it down as you go. That's pretty much all there is to it.
I was able to drill fast and clean using a cobalt bit for steel.

 Heat gun / Wagner Ferno 750. With a spreader nozzle. About $80.00 at big box store.
 I set the heat at 1300 degrees and kept it moving. Once it's warm enough, it starts to bend on its own.
Tested with scrap in order to know how much heat to use.
Also, I left the protective film on the back side as you can see from the picture.

Wood / MDF: $35.00
Plexiglas: $80.00 (36" x 72")
Gun: $80.00 (but you can pickup a cheaper one for less than $30.00)
All thread, nuts and washers less than $30.00
$225.00 all in.

[Hyperacme]

Rick wrote this about drilling holes in plexi windshields.

Little note on this. The Plexi is very brittle and unforgiving.  I know you will want to bend it into place and drill over and into existing holes. Don't. Any stress on the plastic while you are drilling will send a crack along the bend from the new hole up. Better to mark, flatten out, drill and re-position.  I bought a UDP and it was the right size but too expensive. I think we could start our own pool of drawings.

*R

[Hyperacme]

The hinge go's out of stock from time to time ..
Search Google for " Windshield hinge plastic "  or " Gulfcart hinge "   .. Size would be 2 inch or 50mm ..

Windshield hinge plastic ...
https://shop.hamiltonmarine.com/inet/storefront/store.php?mode=searchstore&search%5Bsearchfor%5D=plastic+hinge

[Hyperacme]

CVX windshield gasket (Bottom).  Thanks John !
Looks very similiar to vw beetle fender welting.  Thanks Mike !


Total width   22/32 in.

Distance from edge of bulge to end 14/32 in.

Diameter of bulge  1/4 in.

Thickness of base material  1/16 in.

CVX16 = 82 in. long
CVX18 / CVX20's = 88 in. long


Simolex P Shaped Seals & Gaskets
http://simolex.com/product/p-shaped-silicone-extruded-profile/


Trim-Lok P-Shaped Rubber Seal
https://www.amazon.com/dp/B01CJRIT4A?ref=ppx_pop_mob_ap_share&fbclid=IwY2xjawKl2jRleHRuA2FlbQIxMABicmlkETE1RnNCZEJSTmw3MFhYZGNUAR6wfYxaVBsrwzoGjO7zPMoOo89cuUlcqVbHU2sc7wnFbgCw87ZN-3X2u8wA_A_aem_Eid4TXSGsKAx9Q3ICyWc5Q&th=1

[Hyperacme]

BOAT TAYLOR WINDSHIELD HOLD DOWN HARDWARE~STARCRAFT~FEATHERCRAFT~GLASTRON~MARINE
horsehead_traders eBay store …
https://www.ebay.com/sch/horsehead_traders/m.html?item=361073454913&rt=nc&_trksid=p2047675.l2562


SET OF 4 HIDDEN HOLD DOWN FASTENERS FOR OLDER TAYLOR PLEXIGLASS WRAP-AROUND BOAT WINDSHIELDS.  Set includes 4 OF EACH: threaded paddle fastener, rubber grommet, acorn nut, and lock nut. Works great with our pre-cut 110" Taylor style white rubber window gasket found in our other ebay listings or by contacting us.

[Hyperacme]

From Mark .. On CVX gasket mounting ..

Removed the old foam seal and used two-sided clear tape to hold new gasket in place during install. Worked pretty good and real happy with the end result, except I recommend you make ends long enough to go under both bracket screws. Stretch it slightly before you screw it down so it doesn’t sag or get loose in corners.

[Hyperacme]

This was hidden in other WS info .. If anyone find size that works with there WS .. please post part number.
There are more style on the link, picture are just a few styles.

Taylor made .. Glazing Assembly Vinyls
https://www.taylormadeproducts.com/hardware/glazing-assembly-vinyls/

[Hyperacme]

CV23 Hatch Cover & Latch Bracket

http://forum.cgoamn.com/index.php?topic=4405.msg96613#msg96613

CV23 / CVX23 deck hatch fastener
https://www.fisheriessupply.com/perko-hatch-fastener-or-windshield-keeper-0697/0697dp0chr

[Hyperacme]

From a FB post ...
https://theplasticsguy.com/

Re: Glastron Carlson 1976 CV19ss windshield order and subsequent installation follow-up:
Hey all you Glastron Carlson CV19ss owners out there (as well as other models), get your windshields/acrylics from Brett @ https://theplasticsguy.com
Holy cow, unbeatable customer service. Super fantastic product. I couldn?t be happier!!! Order your Glastron Carlson acrylics from this guy. What a breath of fresh air!
The boat sure looks sweet with that new windshield! Perfect tint. Wow!!!
Note: some pics show the windshield with the protective plastic on the acrylic for test fitting. When I took the plastic off, the windshield is soooo clear. Wow.
Go on, get that new windshield ordered! They do CV23?s as well. Many others too. Best to send in your old broken part(s) for a similar match up as there are variances in every boat. That?s what I did. Perfect match!

From start to finish, how long until you got it back??? ....

It couldn?t have been more than a couple weeks. It took longer as I had to send mine in. Now he has a template. I believe Brett has a clear one for sale immediately. Like I said, best to send yours in for a perfect match. But if you don?t have one, he still has my old one for a template.
And super fast product creation and shipping!!!